The Furious Angels
FA Discussion => Off Topic => Topic started by: Erathaol on April 15, 2009, 01:50:46 am
-
So some time last week I tried turning my computer on and nothing happened. Of course, I was confused and went about doing the normal things to figure out what the problem was. Power was running through my computer, as the little mobo light was lit, but it was simply not powering up.
Eventually, I narrowed it down to the actual power switch. It was broken (what the hell?) and frustratingly near impossible to get to. I had to disassemble my whole tower just to get to it and find out that it was irreparable. So I said "screw it" and ordered a new tower online.
This is why I haven't been on Darkfall (if you've even noticed my absence), but I hope to be back on in less than a week! I'm already starting to go through withdrawals because I can't get my Darkfall fix. Need... to... gank!
-
I dont want excuses!!!! get yo butt in game!!! lol
nahh.. its kewl we understand you situation
-
You can manually jump the power switch pins on the motherboard with a small flathead screwdriver.
Just locate where the power switch connects to the motherboard and use the tip of a knife or a small screwdriver to "jump" or temporarily connect the two pins. Once it powers on you're good.
-
that's right folks, Likwid just told her how to "hot-wire" a computer.
-
That criminal! :p
-
Really now? I think I'll try that. But won't I then have to do that every time thereafter? That could become a major hassle...
-
yes but as a work around until you get your new switch or case. You can just take apart an old case and rig a new power button on your computer.
You should test this as well. Your issue sounds more like a bad power supply than a power switch but that's just guessing. If "hot wiring" it still won't allow it to power up it's another issue.
-
I tried your method and got nothing, so I'm also thinking it's a Power Supply issue. Though, if the Mobo light is on, doesn't that mean that power IS flowing to it? It could be that I'm getting power, but not enough to turn my computer on.
Acting on some advice I found online (they also suggested the screwdriver jumper trick),I unplugged each part one by one to see if my computer turned on with one of them being disconnected. I'm still getting absolutely nothing when I press the power button (or use the screwdriver), no lights or fan activity.
The next thing I'm going to try is swapping out my Power Supply, even though any spare I have lying around is inferior to my current one. Hopefully I'll get at least a little activity with another PS.
EDIT:
I swapped out Power Supplies and sure enough, it powered on. I was so certain that if the Mobo light was on, then the power was on! Oh well, at least now I know the solution (and it's an easy one, too). I'll be back online and back in Darkfall as soon as I can buy a new PS! Huzzah!
Also, thank you Likwid; you're my hero!
-
To test a power supply, disconnect all the motherboard connections, then take a paperclip or small wire and connect it to the Green Wire and any Black Wire it sends a start signal and the power supply will turn on.
Works for most power supplies, sometimes you need to connect a fan or drive to a line or else it'll shut off when it detects no load.
-
To test a power supply, disconnect all the motherboard connections, then take a paperclip or small wire and connect it to the Green Wire and any Black Wire it sends a start signal and the power supply will turn on.
This too. heh lith, not many people know that trick. ;)
Just for all of you, be careful that you don't touch the paperclip when the PS is "hot" and also when it's on make sure the paperclip does not touch anything metal. Just be careful with this. Not sure if that "jump" carries any high voltage but I've never tested it. Better safe than sorry?
Best idea is to take a paperclip, unfold it all the way, and wrap electrical tape around the middle part (the part that won't be shoved inside the PSU connectors.). That way it's a little more safe.
This isn't hotwiring see, we call this Jerry Rigging. ;)
-
Ain't I the luckiest? I got my new PSU (750W, old one was 500W) today and when I installed it everything seemed to work fine, except now I'm not getting any picture on either of my monitors (I use dual-monitors). I tried plugging in just one and then the other, and using a different PCI-E connector from my PSU, and still nothing.
When I was initially fiddling around searching for the problem (when my PSU broke), I think perhaps I was a bit rough on my card and actually broke that tiny white handle hat helps it sit securely in the slot. Do you think I might have damaged my video card and/or the slot on my Mobo? Unfortunately, I don't have another PCI-E video card lying around to swap in and test that way, so that's not an option unless I just go buy a new card and try it out.
I'm hoping one of you techies that know far more about computers than me can help me out. I need Darkfall!
EDIT: Nevermind, all is well. I was stupid and didn't connect the ATX 12V 4-pin to my Mobo... so now my computer is working and I can rejoin you all in Darkfall! Oh, frabjous day!
On a side note, with my new PSU installed, my computer is saying my CPU fan is running too slow. Is this because my PSU is massive for my computer and is shooting too much power? Also, is there a way to simply dial up the fan speed myself so I don't get that annoying beeping? My computer's still running at a constant 50 degrees C so I don't think it's too much of a problem...
-
It may be clogged up with dust. Try blowing it out with a can of air.. If it still does not improve you may need to purchase a new CPU Heatsink/fan combo.
Keep a close eye on your CPU temp. You don't want to overheat.
-
To test a power supply, disconnect all the motherboard connections, then take a paperclip or small wire and connect it to the Green Wire and any Black Wire it sends a start signal and the power supply will turn on.
Works for most power supplies, sometimes you need to connect a fan or drive to a line or else it'll shut off when it detects no load.
That's right folks; Lithium just told her how to turn her computer into a bomb.
(On an unrelated note, I guess I missed the part where Erathaol is female. Here's your stick to keep the boys at bay. You might need it around here!)
-
Wait erathaol is female? i couldve sworn that erathoal was male... but then again.. i could have heard wrong like Tbone did... not that i have anything against females in the guild, i think it's great and actually need more female players... its just that i could have sworn you were male
-
Maybe Yotogi was just mistaken. I dunno!
-
fapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfapfap
er uh... nothing to see here.
-
Sorry to disappoint you all, but I am in fact male. I know I'm pretty quiet on TS, but I'm fairly certain (maybe a bit less now) that I sound male...
Of course, since my computer's been borked I haven't been on TS for a while so that's kinda a moot point.
By the way, does Erathaol seem like a female name? It sure doesn't to me, but I could be in the minority here.
Anyway, back to my computer. My CPU fan is now giving me some real issues. Apparently my computer keeps overheating and shutting itself off to protect itself from damage (I imagine an explosion, but it's usually much less exciting than that). Is this because my PSU is TOO powerful? I didn't think that was possible... with my old PSU I never had any overheating issues, and the fan is exactly the same.
-
Yotogi = lose
I thought you were a dude until I tried to play on words with a quote from Yotogi.
-
Yotogi = lose
its YOTOGI=FAIL!!!
so now its also TBONE=FAIL!!!
-
Lol yea yotogi what were you thinking? haha